Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
This article which follows pertaining to Installing A Bathtub is fairly insightful. Read it for yourself and decide what you think of it.
Mounting a bath tub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult job. If the old tub is readily available, the job can move immediately; if you have to open a wall to remove the old tub and also position the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and are comfortable trying it. As opposed to working with a professional to take control of a halfway-completed task, it is far better to consider using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will assist you install a new bathtub in your shower room if you have already acquired a new bathtub and don't require to change the arrangement of your previous water supply pipes.
Your tools and also material checklist should consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area in between the faucet and also the sink. Secure the faucet in position with the manufacturer offered backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type must be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the tub and additionally check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub should wait until the bath tub has been made use of at the very least when as this will certainly settle it into its last placement.
Preparing for the Setup
First of all, the supporting structure supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final placement.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing issues with dampness and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the market. It is recommended to fit the tiles utilizing water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that blog post about How to Install a Bathtub while scouting around the internet. Do you know someone else who is in to How to Install a Bathtub Yourself? Do not hesitate to promote it. Thank you so much for your time invested reading it.
Precise fixes offered. Report this page